Brick Calculator

Estimate the bricks, cement and sand needed for a brick wall from its length, height and thickness.

m
m
m²
%
₹
Bricks to order (with wastage)
3,623
Bricks without wastage3,450
Volume of brickwork6.90 m³
Cement12 bags (566 kg)
Sand2.36 m³ (83 cft)
Cost of bricks₹28,984

Based on standard modular bricks (190 × 90 × 90 mm) with 10 mm mortar joints. Cement, sand and labour costs are extra.

Brickwork is still the most common way to build walls in Indian homes, and ordering the right number of bricks — along with the cement and sand for mortar — saves both money and delays. The calculator works out the quantities from the wall’s length, height and thickness.

How the estimate works

1. Volume of brickwork

Volume = Length × Height × Thickness

A wall 10 m long and 3 m high, 230 mm (9 inches) thick, has a volume of 6.9 m³.

2. Number of bricks

The standard modular brick is 190 × 90 × 90 mm. With a 10 mm joint, this represents 200 × 100 × 100 mm = 0.002 m³ of volume per brick.

Number of bricks = 6.9 ÷ 0.002 = 3,450. Allowing for 5% wastage due to breakage and cutting gives 3,623 bricks.

  1. Wall volume = 10 × 3 × 0.23 = 6.9 m³
  2. Bricks with mortar = 6.9 ÷ 0.002 = 3,450
  3. Add 5% wastage: about 3,623 bricks
  4. Mortar 1:6: ~12 bags cement, ~2.4 m³ sand
For a 10 m × 3 m wall, 9 inches (230 mm) thick: about 6.9 m³ of brickwork, roughly 3,600 bricks with wastage, 12 bags of cement and 2.4 m³ of sand.

3. Mortar quantity

Mortar generally consists of 25-30% of the total volume of brickwork. Assuming 30% of wet mortar, it would be equal to 2.07 m³. Considering dry volume (×1.33), the dry mortar will be equal to 2.75 m³.

4. Cement and sand (1:6 mix)

Wall thickness options

Wall Thickness Typical use Bricks per m² (approx.)
Half-brick 4.5 in (115 mm) Internal partitions ~55–60
Full brick 9 in (230 mm) External and load-bearing walls ~110–115

Practical points

Approximate cost

Multiply the quantity by the rate at which bricks are available in your locality. For an Example, a brick rate of Rs 8-10, the cost of 3,623 bricks would be Rs 29,000-Rs 36,000. Add to this the cost of bags of cement, sand (mostly measured in cft or per truckload), labour and transportation. The rates vary from city to city and also with the season, so it is best to get quotations from suppliers in your area.

Plastering

Plaster is a separate calculation. So for 12mm internal plaster at 1:6 ratio, a rough guide is 0.15-0.2 bags of cement per square metre. External plaster of 20mm would require a larger number. Then need to calculate the area of the wall on both sides if it is to be plastered on either side.

Brick types compared

Type Typical size Notes
Red clay brick (modular) 190 × 90 × 90 mm Traditional, widely available, strong when well burnt
Fly ash brick 230 × 110 × 75 mm (varies) Uniform shape, uses industrial waste, often cheaper
AAC block 600 × 200 × 100–250 mm Very light, good insulation, needs thin-bed adhesive
Concrete block (solid/hollow) 400 × 200 × 200 mm and others Faster construction, heavier

Due to difference in sizes, the number of units that can be obtained per cubic metre differs greatly. AAC blocks for example may need between 40-80 blocks per cubic metre depending on their thickness while the number of modular bricks is about 500.

Estimating a whole house

For a small house, find out the sum of the lengths of all walls of different thicknesses:

  1. The lengths of external (9-inch) walls and internal (4.5-inch) walls are measured separately.

  2. Multiply by the height of the walls.

  3. Subtract doors and windows.

  4. Multiply by the thickness, to calculate the volumes and determine the calculator for each category.

Example: 50 m of exterior walls and 30 m of interior walls, 3 m in height, with approximately 25 m² of openings in exterior walls and 10 m² in interior walls.

Total: roughly number of bricks are 20,000 — a decent amount to get a quote from suppliers.

Storage on site

Stack the bricks on a suitable surface near the place of use in tidy stacks no more than one and a half or two meters high. Keep them covered during the monsoon season, so they do not absorb the mud. Count the deliveries as they come in the supply is scarce, and it is challenging to recount later.

A note on design

The load bearing capability of walls, walls higher than about 3 m and walls in earth quake prone areas require engineered design incorporating appropriate reinforcements, lintels, and bands. Please use the material estimation calculator for estimation of materials and refer to your contractor/engineer’s drawings for installation.

For concrete works, use the concrete calculator. For plastering, puttying and tiling works, paint and tile calculators will help estimate the subsequent stage works.

Frequently asked questions

How many bricks are in 1 cubic meter of brickwork?

Approximately 500 standard modular bricks (190 × 90 × 90 mm) are required when laid with 10 mm mortar joints. Older non-modular bricks are typically larger, so fewer bricks are used per cubic meter.

How many bricks are there in a 9 "inch wall per Square foot?

A 9-inch thick wall requires approximately 10-11 bricks per square foot of surface area, while a 4.5-inch wall needs about 5 bricks per square foot, prior to considering any wastage.

What is the ratio of mortar in brick work?

Normally 1:6 ratio cement:sand is used for 9 "inch brick work. However, 1:4 ratio cement:sand is used for 4.5 "inch partition walls in order to obtain greater strength. However, always consult your engineer to know the specifications specific to your project.

Should we deduct the area of doors and windows while calculating material?

Yes, you need to calculate the area of all such openings and deduct that from the total area of brick or block work.

This calculator gives estimates for planning and education. It is not financial, tax or professional advice; check important figures with your bank, employer or a qualified adviser. See our disclaimer.